Car Blind spot explained
A blind spot in a vehicle is an area around the vehicle that cannot be directly observed by the driver while at the controls, under existing circumstances.Blind spots exist in a wide range of vehicles: cars, trucks, motorboats and aircraft. Other types of transport have no blind spots at all, such as bicycles, motorcycles and horses.
In transport, driver visibility is the maximum distance at which the driver of a vehicle can see and identify prominent objects around the vehicle. Visibility is primarily determined by weather conditions (see visibility) and by a vehicle's design. The parts of a vehicle that influence visibility include the windshield, the dashboard and the pillars. Good driver visibility is essential to safe road traffic.
Blind spots may occur in the front of the driver when the A-pillar (also called the windshield pillar), side-view mirror, and interior rear-view mirror block a driver's view of the road. Behind the driver, there are additional pillars, headrests, passengers, and cargo, that may reduce visibility.
The blue car's driver sees the green car through his mirrors
but cannot see the red car without turning to check his blind spot.
As one is driving an automobile, blind spots are the areas of the road that cannot be seen while looking forward or through either the rear-view or side mirrors. The most common are the rear quarter blind spots, areas towards the rear of the vehicle on both sides. Vehicles in the adjacent lanes of the road that fall into these blind spots may not be visible using only the car's mirrors. Rear quarter blind spots can be:
- checked by turning one's head briefly (risking rear-end collisions),
- reduced by installing mirrors with larger fields-of-view, or
- eliminated by reducing overlap between side and rear-view mirrors by adjusting side mirrors so the side of the car is barely visible when your head is between the front seats (for the right side mirror) and almost touching the drivers window (for the left side mirror), then checking to be sure you can see cars approaching from behind on either side when on the highway.
Other areas that are sometimes called blind spots are those that are too low to see behind, in front, or to the sides of a vehicle, especially those with a high seating point.
This diagram shows the blocked view in a horizontal-plane in front of the driver. The front-end blind spots caused by this can create problems in traffic situations, such as in roundabouts, intersections, and road crossings. Front-end blind spots are influenced by the following design criteria:
- Distance between the driver and the pillar
- Thickness of the pillar
- The angle of the pillar in a vertical plane side view
- The angle of the pillar in a vertical plane front view
- the form of the pillar straight or arc-form
- Angle of the windshield
- Height of the driver in relation to the dashboard
- Speed of the opposite car
Effects of A-pillar angle on visibility
Most passenger cars have a diagonal pillar as shown in this side view. The angle between the horizon and A-pillar is approximately 40 degrees with a straight pillar that is not too thick. This gives the car a strong, aerodynamic body with an adequately-sized front door.
The sides of a panoramic windshield are curved, which makes it possible to design vertical A-pillars that give the driver maximum forward visibility. However, it is impossible to design an aerodynamic small car with a vertical A-pillar because the more vertical the A-pillar is, the less space the door opening has, and the greater frontal area and coefficient of drag the vehicle will have.
Some modern car designs have an extremely flat A-pillar angle with the horizon. For example, the Pontiac Firebird and Chevrolet Camaro from 1993-2002 had a windshield angle of 68° with the vertical, which equals just 22° with the horizon.
A flatter A-pillar's advantages include reducing the overall drag coefficient and making the car body stronger in a frontal collision, at the expense of reducing driver visibility in a 180° field of view from left to right. A flatter A-pillar (and therefore windscreen) is also a factor when calculating the effects of a collision with a pedestrian. In general a flatter angle will result in a more gentle impact, directing the pedestrian "up and over" rather than directly into the windscreen. This is partically true for cars like the Mercedes A-class which also have a low angled engine cover.
Other disadvantages of a flat windshield angle
- Other traffic can not see the driver through the reflection if the driver can see them.
- The heater needs more time to heat the bigger window surface.
- The flat windshield angle does not let snow slide off easily.
- The driver cannot reach the whole flat window to clean it easily.
Height of the driver
Driver height can also affect visibility.
An A-pillar that is split up and haves a small triangle window (Front Quarter glass) can give a short driver visibility problems. Some cars the windshield is fillet with the roof-line with a big radius. A fillet round A-pillar can give a tall driver visibility problems. Also sometimes the A-pillar can block the driver from seeing motorcyclists.
Also the B-pillar can block the vision of a tall driver in small 4 door cars.
A driver may reduce the size of a blind spot or eliminate it completely by turning their head in the direction of the obstruction. This allows the driver to see better around the obstruction and allows the driver better depth perception.
Visibility in a convertible
Because there is no roof connection between the A- and B- pillar The A-pillars of a convertible automobile have to be stronger and even thicker,
However, with the top down there are no B or C pillars, improving driver visibility behind the driver.
It is best if the dashboard has a non-reflecting dark colored surface.
A small dashboard gives some reflection on the lower part of the windshield.
A big dashboard can give reflection on eye height.
It is best if the inside of the A-pillar has a non-reflecting dark colored surface.
If the side of the window is curved there is less A-pillar reflection.
Light through roof reflection
Some new model cars have a very big sunroof. Sometimes the sunlight through the roof lights up the dashboard and gives a reflection in the windshield.
Other automobile design factors
Other design factors may prevent a manufacturer from maximizing visibility. These include safety, as narrower pillars cannot be made strong as easily as thicker pillars, and size restraints pertaining to aerodynamics, as taller, more vertical windshields create additional drag and reduce fuel efficiency.
Blind Spot Information System
BLIS is an acronym for Blind Spot Information System, a system of protection developed by Volvo. Volvo's previous parent Ford Motor Company has since adapted the system to its Ford, Lincoln (automobile), and Mercury (automobile) brands.
This system was first introduced in the Volvo S80 sedan and produced a visible alert when a car entered the blind spot while a driver was switching lanes, using two door mounted lenses to check the blind spot area for an impending collision.
On Ford products, the system was first introduced in the spring of 2009 on the 2010 Ford Fusion and Fusion Hybrid, 2010 Mercury Milan and Milan Hybrid and 2010 Lincoln MKZ and Mazda 6. This technology was also introduced on the 2010 Mazda CX-9 Grand Touring model.
Some newer and more costly systems use side radar offering better performance and also warn of fast approaching vehicles entering the blind spot.